8rdavcore 0.6b GUI

[Hasw]

Originally Posted by jib

Just out of the blue - are cpus generally able to handle these insane variations in temp and voltage? In theory yes, but has anyone really tested doing things like this for prolonged amounts of time?

I've also thought the (temp increase)/(short time) is maybe a problem, but my CPU makes no problems so far and I really have tormented it
(temp increases from 30 (sensor) to 50 in two minutes). I think it's the same than starting the PC: it also starts from room-temp to maximum during boot.

Originally Posted by jib

OT: Only thing thats missing really is the ability to software-control my fans. As it turns out speedfan doesnt work with 8rda+ and I haven't found any others that do.

I tought the Winbond RPM outputs on the 8RDA+ are not used to controll the FANS? So it isn't possible.

[Hasw]

Version 0.7.6b is now available:

http://www.hasw.net/8rdavcore/

Changes:

0.7.6b:
- Added VCore-presets to AutoFSB
- Fixed sys-temp display (nf7vcore)
- Added second AutoFSB delay option
- Moves now to tray if minimized
- Corrected Vdd trackbar setting at startup (8rdavcore)
- Increased VCore change delay
- Changed CPU load code
- Added "reset settings before exit" option
- Fixed "Current Vagp" displays Vdd
- Added max. CPU temp to AutoFSB
- Added some hints

[mal0]

do have a newer one for linux, too??

[Hasw]

Not yet finished. In one or two weeks maybe.

[mal0]

to make things clear:
i don't control my fans via 8rda+ but by an additional fan control which can be controlled through software.

@hasw: i think i can wait so long

[Speedy-J]

@Hasw
AutoVcore is not responding to the AutoFSB ,what could this mean ?
It does not lower Vcore when trhottling down from 215Mhz FSB to 174Mhz FSB

Regards :Speedy-J

[Hasw]

Originally Posted by Speedy-J

@Hasw
AutoVcore is not responding to the AutoFSB ,what could this mean ?
It does not lower Vcore when trhottling down from 215Mhz FSB to 174Mhz FSB

Regards :Speedy-J

Which version do you use? There was a problem in 0.7.6 if the numbers were comma-separated and not with a point. This is fixed in 0.7.7.

[Speedy-J]

I was using the old version ,now i have the newer version and the problem is still there.
I looked in the presets.ini for the voltages and it show me (1,7V) for the lower vcore setting and 2 for the high vcore setting setting.
I think the problem with the comma seperated is still there ?

[Hasw]

No, it can now use both, for example 1,7 or 1.7.

[Hasw]

New version 0.7.8b:

http://www.hasw.net/8rdavcore/

0.7.8b:
- Now shows Fans > 670 RPM
- Added sensor update frequency
- Added FSB change delay for AutoFSB
- Now it's possible to change VCore and FSB in one step
- Save settings on exit
- Added -A command-line option for AutoFSB
- Added more debug-messages to giveio service handler
- Changed CPU load code

[jcool]

Originally Posted by Hasw

New version 0.7.8b:

http://www.hasw.net/8rdavcore/

0.7.8b:
- Now shows Fans > 670 RPM
- Added sensor update frequency
- Added FSB change delay for AutoFSB
- Now it's possible to change VCore and FSB in one step
- Save settings on exit
- Added -A command-line option for AutoFSB
- Added more debug-messages to giveio service handler
- Changed CPU load code

mmh, cpu load doesn't work for me, just shows 0% all the time no matter what...
But apart from that no bugs, at least not for me

[mat9v]

Really works great !
jcool - check sensor update frequency - was at 0 seconds after first run and no settings would show changes for me... just set it to 1 or more and watch
Best utility for great MB. Made a simple controller for fan speed, now with that proggy I can make my comp almost silent
Only thing for me to do is to combine that with a thermal sensor to automaticaly regulate fan speed.... something to think about for next weekend

[jcool]

aaahhhh I see =)
Now it works thx

[mat9v]

Hmm... would it be possible to add sensor readings for 5 and 12 V ?
Wouldn't have to use any other monitoring utility then (I use USDM now, simple and free but would be happier with one util )

[Speedy-J]

Everything works okay now ,I am very satisfied with the program
Keep up the good work !

[epoxer]

This little program is really great. I have one small suggestion ... HASW could you add the RUN AT WINDOWS STARTUP option ??

[nfrenay]

Originally Posted by epoxer

This little program is really great. I have one small suggestion ... HASW could you add the RUN AT WINDOWS STARTUP option ??

You know you can just create a shortcut to it in the Start - Programs - Startup folder right?

(Not very sure about the name in English as my Windows is in Portuguese .

[Hasw]

@mat9v: yes
@epoxer: <nfrenay> ... and add a -A: 8rdavcore.exe -A

[epoxer]

Originally Posted by Hasw

@mat9v: yes
@epoxer: <nfrenay> ... and add a -A: 8rdavcore.exe -A

thx for the tip ...

[MiGGinZ]

I get this error every time I try run the program.

Error:I2C-init-> Cannot open GiveIO handle