| |||||||
| EPoX MotherBoards EPoX Intel and AMD Motherboards. |
 |
| | LinkBack | Thread Tools | Rate Thread |
3rd August, 2002, 11:19 PM
| ||||
| ||||
| USDM and TurboLite 420w PS-(8K3A+) oK-iM writing a review of the new Chieftec Aluminum server cases with 420w ps- it is sweet........... but every 5minutes i get a little "warning 3/88v line has exceded normal operating areas- choose one of the 5 folowing...- Ok- i open it and it always says its fine!!!!!!!UGGGGG! Anyhelp? Spyder
__________________ ~The Spyder~ I7 965, 6gigs, ASUS, 4870 X2, WD640 AALS Lian Li PC65 Nikon D700, 24-70, 70-200 2.8, SB 800x2 1993 Mazda Rx7 R1 345whp. 2008 Mazda 3 Hatch       |
|
4th August, 2002, 05:21 AM
| ||||
| ||||
| What is '3/88v '...never heard of it. Anyway, I'd bag USDM for the moment and install Motherboard Monitor 5 to see whats going on with your voltages. What does BIOS report for voltages? http://mbm.livewiredev.com/
__________________ |
|
4th August, 2002, 03:41 PM
| ||||
| ||||
| No idea what it is either- put MBM5 on and it ****ed the whole sytem up- reading 90c from both temp monitors now............ reinstalling windows and the temp montiors got me my normal temps again- im just putting the enermax back in......... Looks like this PS wont be getting to good of a review........
__________________ ~The Spyder~ I7 965, 6gigs, ASUS, 4870 X2, WD640 AALS Lian Li PC65 Nikon D700, 24-70, 70-200 2.8, SB 800x2 1993 Mazda Rx7 R1 345whp. 2008 Mazda 3 Hatch |
|
4th August, 2002, 04:50 PM
| ||||
| ||||
| Did you select Winbond 2 Diode as your CPU sensor and Winbond 1 as your case sensor in MBM5?. It's a common mistake to get those settings wrong. You should have posted back, we could have saved you a rebuild.
__________________ Last edited by Harryc; 5th August, 2002 at 04:46 AM. |
|
4th August, 2002, 04:59 PM
| ||||
| ||||
| Winbond 1= Cpu Winbond 2= Case
__________________ ~The Spyder~ I7 965, 6gigs, ASUS, 4870 X2, WD640 AALS Lian Li PC65 Nikon D700, 24-70, 70-200 2.8, SB 800x2 1993 Mazda Rx7 R1 345whp. 2008 Mazda 3 Hatch |
|
4th August, 2002, 07:03 PM
| ||||
| ||||
| LOL- USDM read the same thing to however..
__________________ ~The Spyder~ I7 965, 6gigs, ASUS, 4870 X2, WD640 AALS Lian Li PC65 Nikon D700, 24-70, 70-200 2.8, SB 800x2 1993 Mazda Rx7 R1 345whp. 2008 Mazda 3 Hatch |
|
5th August, 2002, 04:50 AM
| ||||
| ||||
| I'm not sure why that was happening, very strange. Nevertheless, if you did not select Winbond 2 Diode as your CPU sensor and Winbond 1 as your case sensor in Motherboard Monitor, your temps would be way off.
__________________ Last edited by Harryc; 7th August, 2002 at 04:58 AM. |
|
5th August, 2002, 09:27 AM
| |||
| |||
| I get the same thing with my 8k3a+ and mbm-usdm. I just got tired of messing with 'em, if my rig crashes then it's too hot. I don't think the cpu temp is even close in the bios, I run naked now.
__________________ |
|
5th August, 2002, 11:05 AM
| ||||
| ||||
 temps Vcool, install it. watch temps as read from the internal diode, halt command lowers temps for everyday use. it displays fan rpms and temps, what else do you need??? voltages can be observed at boot with the PC Health activated. baldy 
__________________ Opty's 939 single and dual, DFI, AsRock, Gskill & Team, clocked of course...   |
|
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | |
| Rate This Thread | |
| |
Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| OCZ 420w killing MOBOS | Gunny2times | CRASHED! | 5 | 29th March, 2005 03:17 PM |
| Usdm | chrisbard | EPoX MotherBoards | 11 | 21st November, 2003 04:40 AM |
| NEW USDM v2 | hchu | EPoX MotherBoards | 7 | 5th September, 2003 05:54 PM |
| USDM for Epox 8K3A+ | Thesi | EPoX MotherBoards | 1 | 19th July, 2003 01:20 AM |
| Usdm | The Spyder | EPoX MotherBoards | 3 | 8th September, 2002 04:57 AM |
