AOA Forums

AOA Forums (http://www.aoaforums.com/forum/)
-   Intel Motherboards & CPUs (http://www.aoaforums.com/forum/5-intel-motherboards-and-cpus/)
-   -   3.0C SL6WK, Epox, 4000 Gold Rev.2 Unleashed!! (http://www.aoaforums.com/forum/intel-motherboards-and-cpus/27502-3-0c-sl6wk-epox-4000-gold.html)

weldzilla 22nd October, 2004 04:43 AM

3.0C SL6WK, Epox, 3200 Platinum Rev.2 Unleashed!!
 
Well here is my latest processor now working in combination with Motherboard and memory. Why would anyone who owns an intel Processor not use this Epox 4PDA2+Ver.2 board??? It is truly the best I have ever used!!


WZ

weldzilla 22nd October, 2004 05:02 AM

Sorry about that here is the pic
http://img.photobucket.com/albums/v2...illa/fixed.jpg

WZ

cadaveca 22nd October, 2004 05:22 AM

sweetness. 4ghz...and intel abandoned 4ghz! They should be taking lessons from you!

weldzilla 22nd October, 2004 05:34 AM

Cadaveca
 
now you see why i am willing to part with my 2.4C. This chip is unreal!!


WZ

nki69c 22nd October, 2004 05:37 AM

What is the temp like on that? That is pretty impressive. Did you get a lucky chip or is that common for the C?

alexkerhead 22nd October, 2004 05:47 AM

very nice weld, I am sooo jealous

weldzilla 22nd October, 2004 01:09 PM

as well you should be alex!! My idle temp is 33C. has yet to go above 50C. Not sure if it is the chip. Does not seem to matter what I pug into this board. Once secured it takes off. A friend brought over a 2.6C that he said was no good cuz he coul;d get past 3.2. I wasn't too thrilled about pulling my block off and pulling my processor to try his chip. But, I did. I asked him what voltages he had tried. He had gone to 1.75 on his abit IS-7. he thought I was going to spend the whole night increasing the fsb 1 mhz at a time! I turned the volts up to 1.7 which is about 1.632 on this board. I set the fsb @ 280 and fired it up. It came right to life!! running great at 3640mhz.
Now he has air cooling, and he has Kingston budget ram. I would not blame the board yet. I am going over this weeekend to check it all out. Just everything I plug into this board flies! I'll run it on the 5:4 divider and show you just how far it will go!

WZ

Pitch 22nd October, 2004 04:18 PM

Quote:

Originally Posted by nki69c
What is the temp like on that? That is pretty impressive. Did you get a lucky chip or is that common for the C?

Not really.

I had a 3.0C (before I fried it, but it wouldn't do 3.7+

seeing as I killed it, I got a replacement which when it has power [:mad:] it does 4.1 bench stable. I guess it's just a certain number. If I get a min, I'll find out what code mine is.

weldzilla 23rd October, 2004 12:47 AM

Very Cool on the 5:4 divider
 
1 Attachment(s)
Not sure why but when on the 5:4 divider it runs at 28C with a case temp of 20C Which allows for even more extreme OC. So I turned it up a bit just to get an idea of what it might do. Well let me tell you it will do alot!!
Check it out!!

WZ

alexkerhead 23rd October, 2004 02:07 AM

nice, very nice

Confused 24th October, 2004 03:19 PM

Quote:

Originally Posted by weldzilla
Well here is my latest processor now working in combination with Motherboard and memory. Why would anyone who owns an intel Processor not use this Epox 4PDA2+Ver.2 board??? It is truly the best I have ever used!!


WZ

Congratulations. May I ask if you're 3.0c is a 12 or 30 capper, and if you think it would make any difference in your results using a 12 or 30?

Zhero 30th October, 2004 01:52 PM

wz, What Bios are you using? And How did you get pat enabled with 1.1

weldzilla 31st October, 2004 03:22 AM

Here is the bios I am using. i will tell you it is only for the 4PDA2+ Boards.
BIOS: 4PD24319.BIN (1A00)
BIOS Date: 03/19/2004
The main reason for this update was to accomodate the prescott processor.
On my board you need only to set your mem to max to enable pat in 1:1
Quite frankly I never understood the release of the 4PDA5 board. Although those I know that have them, like them. Myself I am going to get another 4PDA2+ board. My wife is going to let me build her a system based on it. Lucky girl.

WZ

weldzilla 31st October, 2004 03:26 AM

Should let you all know that the PC4000 gold Rev.2 is gone. Returned to OCZ. They are sending me 2 x 512 chips of PC3200 Platinum Rev.2. Hoped to have it by tuesday as I get election day off. thought I would go vote early then play with new mem all day. however it now looks as though it will not arrive before wedsnesday. So I have to be patient.

WZ

weldzilla 31st October, 2004 03:36 AM

My proceesor is a SL6WK 30 capper. I have never payed with any other 3.0C processor. so I can't say if 30 is better than 12. That is what I here though.
I do know every processor I stick in my board goes far beyond what it did in the board it came from. I must tell you I am done testing proceesors for guys. As I have to remove their prossy's for them , clean them, Use up my AS5, Remove mine clean it up istall theirs test it, remove it and clean it ,re-apply MY AS5 and reinstall in their system,then do all that to mine to get it back into my system. It is a pain in the ass. Although it has helped EPOX to seel some more boards. I get nothing for it. But, this has only been done for my closest friends. It's true I built everyone of their systems.
This was before I built mine or we would of all had EPOX boards from the start!!


WZ

alexkerhead 31st October, 2004 03:50 AM

Quote:

Originally Posted by weldzilla
My proceesor is a SL6WK 30 capper. I have never payed with any other 3.0C processor. so I can't say if 30 is better than 12. That is what I here though.
I do know every processor I stick in my board goes far beyond what it did in the board it came from. I must tell you I am done testing proceesors for guys. As I have to remove their prossy's for them , clean them, Use up my AS5, Remove mine clean it up istall theirs test it, remove it and clean it ,re-apply MY AS5 and reinstall in their system,then do all that to mine to get it back into my system. It is a pain in the ass. Although it has helped EPOX to seel some more boards. I get nothing for it. But, this has only been done for my closest friends. It's true I built everyone of their systems.
This was before I built mine or we would of all had EPOX boards from the start!!


WZ

start a testing business.
charge $35 to test a cpu

weldzilla 31st October, 2004 04:31 AM

I like your thinking alex. Moooooo Moneyyyyyyy. I spent most of the day at a friends house. figuring out his software mess. It all came back to one little glitch. he did not check the english,north america box . On his power dvd so he could not do DVD re-editing using his pinnacle system. Then I spent another 2 hours giving him a short coarse in editing. I raised his 2.4C sl6z3 to a 3.0 running his kingston mem at 250 1:1.
this was all on an Abit IS-7 mobo. He was very pleased with the boost. I installed speedfan to keep an eye on his temps. They were fine. His V-core remained at stock setting. His mem is at 2.8v.

WZ

alexkerhead 31st October, 2004 04:44 AM

Quote:

Originally Posted by weldzilla
I like your thinking alex. Moooooo Moneyyyyyyy. I spent most of the day at a friends house. figuring out his software mess. It all came back to one little glitch. he did not check the english,north america box . On his power dvd so he could not do DVD re-editing using his pinnacle system. Then I spent another 2 hours giving him a short coarse in editing. I raised his 2.4C sl6z3 to a 3.0 running his kingston mem at 250 1:1.
this was all on an Abit IS-7 mobo. He was very pleased with the boost. I installed speedfan to keep an eye on his temps. They were fine. His V-core remained at stock setting. His mem is at 2.8v.

WZ

Now all I need is a "C" model with good stepping/ :evil:

weldzilla 31st October, 2004 04:50 AM

Sell a couple of your systems and put one together!!

alexkerhead 31st October, 2004 07:51 AM

Quote:

Originally Posted by weldzilla
Sell a couple of your systems and put one together!!

i only have 3 left..lol
I am still trying to pay the car off.. :crazy:
i almost have enough for the RAM tho.


All times are GMT +1. The time now is 04:00 AM.


Copyright ©2001 - 2010, AOA Forums


Search Engine Friendly URLs by vBSEO 3.3.0