22nd May, 2002, 01:51 AM
| ||||
| ||||
| Blow hole location?? Do I put the 2 fans on top like I have the other 2 case's or on the top-side as in the pic? Give me a hole saw and watch out 
__________________ Ep0x 8K3A, XP1700+ T-bred JIUHB-(310)XPMW,DLT3C,189x12.5=2.36 1 gig mb PC 3200 Corsair . Swiftech H20 setup with MCW372 block. eVGA 6800 GT. 350 w Sparkle PS. XFIRE= rottys      |
|
22nd May, 2002, 02:22 AM
| ||||
| ||||
| Assuming you're close to neutral on air flow (in/out) I think the on top would be most effective at getting hot air out of the case since heat will rise and potentially get trapped at the top. It would also direct airflow through more of the case and probably have a better chance at avoiding hot pockets. (ever notice how hot a DVDROM can get?)
__________________  |
|
22nd May, 2002, 02:22 AM
| ||||
| ||||
| I personally have put them 1 on top of eachother. 1 blowing on the AGP slot and another directly on the CPU fan. It's a little thing but remember this, you should try to balance cfm in and out to be roughly equal but if not, the majority should be in. HTH 
__________________ Main Rig: Gigabyte GA-965P-DQ6 (rev. 1.0) cooled by the Monster Water Cooling Setup HTPC One BIG Case Asus 8 CORE Monster Current PC Count: ASROCK: 1 * BIOSTAR: 1 * ASUS: 5 * CHAINTECH: 7 * GIGABYTE: 2 *IWILL: 1 * MSI: 3* TYAN: 2 175+ GHZ total power for PC Perspective Killer Frogs Climate Prediction Team as The Uncle B's!! and more coming all the time! I'm the Uncle your Aunt won't talk about. Go ahead and pull my finger! |
|
22nd May, 2002, 03:06 AM
| ||||
| ||||
| Ok so they are going on top, just drilled out the rivits, now to setup for the holes, then cut cut, drill drill. 2x80mm in 2x80mm out. These are on the sys with the AX-7, that think kickz @$$ big time.
__________________ Ep0x 8K3A, XP1700+ T-bred JIUHB-(310)XPMW,DLT3C,189x12.5=2.36 1 gig mb PC 3200 Corsair . Swiftech H20 setup with MCW372 block. eVGA 6800 GT. 350 w Sparkle PS. XFIRE= rottys |
|
22nd May, 2002, 04:38 AM
| ||||
| ||||
| There we go now, it's 3 in, 2 out, forgot about the one bottom front.
__________________ Ep0x 8K3A, XP1700+ T-bred JIUHB-(310)XPMW,DLT3C,189x12.5=2.36 1 gig mb PC 3200 Corsair . Swiftech H20 setup with MCW372 block. eVGA 6800 GT. 350 w Sparkle PS. XFIRE= rottys |
|
22nd May, 2002, 05:31 AM
| ||||
| ||||
| Exclent job- i did a similar job earlier this month :-d Spyder
__________________ ~The Spyder~ I7 965, 6gigs, ASUS, 4870 X2, WD640 AALS Lian Li PC65 Nikon D700, 24-70, 70-200 2.8, SB 800x2 1993 Mazda Rx7 R1 345whp. 2008 Mazda 3 Hatch  |
|
22nd May, 2002, 06:42 AM
| ||||
| ||||
| Quote:
__________________ Ep0x 8K3A, XP1700+ T-bred JIUHB-(310)XPMW,DLT3C,189x12.5=2.36 1 gig mb PC 3200 Corsair . Swiftech H20 setup with MCW372 block. eVGA 6800 GT. 350 w Sparkle PS. XFIRE= rottys |
|
22nd May, 2002, 06:50 AM
| ||||
| ||||
| Quote:
__________________ Then, as it was, then again it will be Though the course may change, rivers will always reach the sea. ---------------------------------------------- |
 |
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | |
| Rate This Thread | |
| |
Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Sussex,UK - Need location advice please. | kellamne | AOA's Community Support | 3 | 11th July, 2006 02:26 PM |
| finally a good location | kat | Random Nonsense! | 4 | 8th September, 2003 04:17 AM |
| Memory Location | valdor | EPoX MotherBoards | 1 | 20th June, 2003 12:24 AM |
| One hole fixed, one new hole created. | cloasters | Data Security | 0 | 19th June, 2003 08:26 PM |
| Location, location, location. | Rackne | Random Nonsense! | 4 | 17th January, 2003 05:27 PM |
