AOA Forums

AOA Forums (http://www.aoaforums.com/forum/index.php)
-   Hardware Hacking (http://www.aoaforums.com/forum/forumdisplay.php?f=39)
-   -   -> Mod your 6800GS AGP to Ultra Extreme with coolermod! (http://www.aoaforums.com/forum/showthread.php?t=35737)

Deadman93723 25th June, 2006 09:49 PM

Quote:

Originally Posted by dsio
Definitely a good idea. Did you find the threads with the volt modding guides?

No I didn't, but that is ok, I don't want to do any hardware mods while I am still under warranty. eVGA has loose rules for warranty, but they still frown on modding the circuit board.

dsio 25th June, 2006 10:31 PM

Its not an actual mod to the board as such. What you do is find a certain surface mount resistor. You lower the resistance of that resistor, while measuring, to get the desired volt mod.

To lower that resistance, you <could> use a soldered in variable resistor, but the best way, is to just use a 2B pencil, since its very mildly conductive. When done with it, you simply wipe the pencil trace off the top.

Deadman93723 26th June, 2006 12:38 AM

Quote:

Originally Posted by dsio
Its not an actual mod to the board as such. What you do is find a certain surface mount resistor. You lower the resistance of that resistor, while measuring, to get the desired volt mod.

To lower that resistance, you <could> use a soldered in variable resistor, but the best way, is to just use a 2B pencil, since its very mildly conductive. When done with it, you simply wipe the pencil trace off the top.

Do you know where I can find a guide to do the pencil mod?

dsio 26th June, 2006 10:34 AM

http://www.aoaforums.com/forum/graph...ghlight=pencil

Thats the previous thread on volt modding, with pictures for the pencil mod.

If you really do something serious with the cooling, and that mod, expect over 500Mhz on water cooling, and in some cases over 600Mhz. It really makes an absolutely massive difference, but that is with a very high volt mod and water.

A minor volt mod, running with stock, or good air cooling, will get you a nice little bump. I would advise doing something with your cooling first though.

1: You could try removing the stock heatsink, removing the thermal paste, and using a quality layer of arctic silver 5 to improve thermal conductivity.

2: You could lap and polish your stock HSF

3: You could try this coolermod (on the first page of this thread)

4: You could try a zalman cooler, as the NVsilencers are not the /best/ coolers anymore.

NarkotikBuzz 26th June, 2006 04:23 PM

I am having an interesting issue with my 6800le....i currently have it clocked 420/820, which it takes just fine, it will probably go much higher, but now, whenever i restart my computer, the memory reverts back to stock speeds, the core speed stays the same, just the memory changes, any idea why this is happening?

dsio 26th June, 2006 05:10 PM

What program are you using to set your overclock speeds?

Deadman93723 26th June, 2006 05:32 PM

Quote:

Originally Posted by dsio
http://www.aoaforums.com/forum/graph...ghlight=pencil

Thats the previous thread on volt modding, with pictures for the pencil mod.

If you really do something serious with the cooling, and that mod, expect over 500Mhz on water cooling, and in some cases over 600Mhz. It really makes an absolutely massive difference, but that is with a very high volt mod and water.

A minor volt mod, running with stock, or good air cooling, will get you a nice little bump. I would advise doing something with your cooling first though.

1: You could try removing the stock heatsink, removing the thermal paste, and using a quality layer of arctic silver 5 to improve thermal conductivity.

2: You could lap and polish your stock HSF

3: You could try this coolermod (on the first page of this thread)

4: You could try a zalman cooler, as the NVsilencers are not the /best/ coolers anymore.

I already have a NV silencer on the card with AS5, it doesn't go above 62c load and the AS5 hasn't even totally cured yet. Thanks for the link, I'll try it sometime soon.

NarkotikBuzz 26th June, 2006 06:48 PM

I am using the Winfast Speedrunner software that comes with the card, it works best i think, but after i set the clocks, i go into the regular "classic" control panel, make sure it reads the same speeds, then i click the box that says "set these speeds at startup", it gives me the OK, and everything is fine from there, until i restart, then the memory speed reverts. I am totally confused on this one. I have tried setting the clocks with the regular CP, but when i try it, it hardly lets me raise it at all, and it says the speeds fail the test, even though when i set it with winfast, the card runs just fine at the faster speeds, i dont get it.

Deadman93723 26th June, 2006 07:26 PM

Quote:

Originally Posted by NarkotikBuzz
I am using the Winfast Speedrunner software that comes with the card, it works best i think, but after i set the clocks, i go into the regular "classic" control panel, make sure it reads the same speeds, then i click the box that says "set these speeds at startup", it gives me the OK, and everything is fine from there, until i restart, then the memory speed reverts. I am totally confused on this one. I have tried setting the clocks with the regular CP, but when i try it, it hardly lets me raise it at all, and it says the speeds fail the test, even though when i set it with winfast, the card runs just fine at the faster speeds, i dont get it.

You should use either Coolbits 2 or Rivatuner, they work the best.

NarkotikBuzz 26th June, 2006 07:43 PM

I have solved the problem. All i had to do was set the 2D memory setting the same as the 3D, and it keeps all the settings the same after a restart. As of now i actually have the card clocked at 425/850 and i am pretty sure i can push it even further, as i am not getting any artifacts at all, and my temps still max out around 65-68. Later on i am gonna try pushing it a little more and really see what this card will do, i love this Leadtek.:D As far as OC software, i have tried them all, and for my card, the Winfast Speedrunner software works better than anything, and has allowed me much higher clocks than any other software.

mbataka 30th June, 2006 05:10 PM

Diablotel AGP 6800GS problem
 
Hi, all

I own Diablotek 6800GS 512, purchased from geeks.com.

This card from the beginning started giving some errors, its artfiacts on boot screen and after windows load flashing of lcd every 1sec. It might be factory faulty card, but its not happening in safe mode. After drivers load its beginning to happen. In the before bios Shows nvidia 6800GTS. (GTS???)

And in the bios editor it not says any manufacturer info and GPU info. ONLY SAYS 6800GS(BR02)

So i think our friends, chinese masters did some stupid bios mistake in this card. I can proceed RMA but before RMA i want to play little bit. So anyone have a same card and any similar problems?. If some one have a proper bios could post here for experiments?. Any advice and any directions in this problem?
Thanks guys.

I'll post asap some screen shoot related to this card. Sorry for bad english :)


=== The following is an automatically generated message ===


This is mbataka's first post. The Welcome thread is here. Please drop by the Welcome thread and give mbataka a warm AOA welcome there.

dsio 30th June, 2006 05:54 PM

When you uninstall your drivers, does it change / improve anything?

Also, starting in safe mode, does that make any changes?

Deadman93723 30th June, 2006 07:15 PM

Does anyone have any suggestions on getting my eVGA 6800gs agp passed 415/1150.

dsio 30th June, 2006 07:19 PM

Are you using the 91.33 drivers? They seam to overclock better than previous versions.

Deadman93723 30th June, 2006 08:10 PM

Quote:

Originally Posted by dsio
Are you using the 91.33 drivers? They seam to overclock better than previous versions.

I'm still using 84.21, I haven't tried 91.33, because I seem to have trouble with anything but the 84.21. This card is very moody.

mbataka 1st July, 2006 06:27 AM

Quote:

Originally Posted by dsio
When you uninstall your drivers, does it change / improve anything?

Also, starting in safe mode, does that make any changes?

After uninstalling, same in the bios post, but in the windows everything fine.

In safe mode its mean not loading the drivers. then its fine. But without drivers its nouse right. i tryed almost every driver, all the same. In the bios edit it says: Core: 425MHZ Memory: 500MHZ , so i'm doubting its a NV42 Chip.

dsio 1st July, 2006 08:30 AM

What drivers were you using before you unistalled them mbataka?

And deadman, I would try the 91.33s, they're quite good. Grab the TRU modified ones while you're at it. They do seam to let you overclock a bit higher (91.33s in general)

NarkotikBuzz 1st July, 2006 11:57 AM

Dsio, i think you mean the 91.31's.....we just got the 91.33's yesterday, and there is not TRU modified version of them yet. I tried the new 91.33's and had a ton of problems, and they are BETA drivers. Please just try the 91.31 Xtreme-G modified drivers, they work very well, and overclock great.

Deadman93723 1st July, 2006 06:53 PM

Quote:

Originally Posted by NarkotikBuzz
Dsio, i think you mean the 91.31's.....we just got the 91.33's yesterday, and there is not TRU modified version of them yet. I tried the new 91.33's and had a ton of problems, and they are BETA drivers. Please just try the 91.31 Xtreme-G modified drivers, they work very well, and overclock great.

I'll give it a shot.

NarkotikBuzz 1st July, 2006 10:14 PM

Let us know if they work for you, i have had great success with this set.


All times are GMT +1. The time now is 01:16 AM.


Copyright ©2001 - 2010, AOA Forums


Search Engine Friendly URLs by vBSEO 3.3.0